Tingnan ang mga detalye para sa mga detalye ng produkto.
ACS716KLATR-25CB-T
Introduction
The ACS716KLATR-25CB-T is a current sensor belonging to the category of integrated circuits. It is commonly used for measuring current in various electronic applications. This entry provides an overview of the basic information, specifications, pin configuration, functional features, advantages and disadvantages, working principles, application field plans, and alternative models of the ACS716KLATR-25CB-T.
Basic Information Overview
- Category: Integrated Circuits
- Use: Current sensing in electronic applications
- Characteristics: High accuracy, low offset voltage, wide operating temperature range
- Package: Surface Mount
- Essence: Accurate current measurement
- Packaging/Quantity: Tape & Reel (3000 units per reel)
Specifications
- Operating Voltage: 5V
- Sensitivity: 25mV/A
- Operating Temperature Range: -40°C to 125°C
- Output Type: Analog Voltage
- Accuracy: ±1.5%
- Bandwidth: 80kHz
Detailed Pin Configuration
- VCC
- GND
- Output
- NC (Not Connected)
- NC
- NC
- NC
- NC
Functional Features
- High accuracy current sensing
- Low power consumption
- Wide operating temperature range
- Small form factor
Advantages and Disadvantages
Advantages
- High accuracy
- Wide operating temperature range
- Low offset voltage
Disadvantages
- Limited bandwidth
- Analog output may require additional signal conditioning
Working Principles
The ACS716KLATR-25CB-T utilizes the Hall effect to measure current. When current flows through the device, it generates a magnetic field which is sensed by the integrated Hall sensor. This results in a proportional output voltage that can be measured to determine the current passing through the sensor.
Detailed Application Field Plans
The ACS716KLATR-25CB-T is suitable for a wide range of applications including: - Motor control systems - Power management systems - Battery monitoring - Overcurrent protection circuits
Detailed and Complete Alternative Models
Some alternative models to the ACS716KLATR-25CB-T include: - ACS712ELCTR-05B-T - ACS758LCB-100B-PFF-T - INA219AIDCNR
In conclusion, the ACS716KLATR-25CB-T is a versatile current sensor with high accuracy and a wide operating temperature range, making it suitable for various electronic applications.
[Word Count: 349]
Maglista ng 10 karaniwang tanong at sagot na nauugnay sa aplikasyon ng ACS716KLATR-25CB-T sa mga teknikal na solusyon
What is the ACS716KLATR-25CB-T?
- The ACS716KLATR-25CB-T is a high-precision, fully integrated current sensor based on the Hall effect.
What is the operating voltage range of the ACS716KLATR-25CB-T?
- The operating voltage range of the ACS716KLATR-25CB-T is 3.0V to 5.5V.
What is the output voltage range of the ACS716KLATR-25CB-T?
- The output voltage range of the ACS716KLATR-25CB-T is typically ±625mV at 25A.
What is the typical accuracy of the ACS716KLATR-25CB-T?
- The typical accuracy of the ACS716KLATR-25CB-T is ±1.5% over the full temperature range.
What is the package type of the ACS716KLATR-25CB-T?
- The ACS716KLATR-25CB-T comes in a small, low-profile surface-mount package.
What are the typical applications for the ACS716KLATR-25CB-T?
- Typical applications include motor control, power management, and overcurrent fault protection in automotive, industrial, and consumer systems.
What is the maximum continuous current that the ACS716KLATR-25CB-T can measure?
- The ACS716KLATR-25CB-T can measure up to 25A of continuous current.
Does the ACS716KLATR-25CB-T require an external power supply?
- Yes, the ACS716KLATR-25CB-T requires an external power supply within its specified operating voltage range.
Is the ACS716KLATR-25CB-T suitable for high-temperature environments?
- Yes, the ACS716KLATR-25CB-T is designed to operate reliably in high-temperature environments.
Can the ACS716KLATR-25CB-T be used for bidirectional current sensing?
- Yes, the ACS716KLATR-25CB-T supports bidirectional current sensing with appropriate circuitry.